收藏本站
AL9910/ AL9910A/ AL9910-5
Applications Information (cont.)
DC-DC Buck LED Driver
The design procedure for an ac input buck LED driver outlined in the previous chapters equally applies DC input LED drivers.
When driving long LED chains care should be taken not to induce SBO – maximum LED chain voltage should be less half of V IN . So either
maximum duty cycle should be kept below 50% or use of constant off-time removes this issue.
DC-DC Boost LED Driver
Due to the topology of the AL9910 LED driver-controller it is capable of being used in boost configurations – at reduced accuracy. The accuracy
can be improved by measuring the LED current with an op amp and use the op amp’s output to drive the LD pin.
A Boost LED driver is used when the forward voltage drop of the LED string is higher than the input supply voltage. For example, the Boost
topology can be appropriate when input voltage is supplied by a 48V power supply and the LED string consists of twenty HB LEDs, as the case
may be for a street light.
L1
C1
V DD
V IN
AL9910/A
Q1
D1
V IN
PWM_D
GATE
C2
LD
R OSC
GND
CS
C3
R OSC
R SENSE
Figure 5. Boost LED Driver
In a Boost converter, when the external MOSFET is ON the energy is stored in the inductor which is then delivered to the output when the external
MOSFET switches OFF. If the energy stored in the inductor is not fully depleted by the next switching cycle (continuous conduction mode) the DC
conversion between input and output voltage is given by:
V OUT =
V IN
1 ? D
D =
V OUT ? V IN
V OUT
From the switching frequency, f OSC , the on-time of the MOSFET can be calculated:
t ON =
D
f OSC
From this the required inductor value can be determined by:
L =
V IN ? t ON
0 . 3 ? I LED
The Boost topology LED driver requires an output capacitor to deliver current to the LED string during the time that the external MOSFET is on.
In boost LED driver topologies if the LEDs should become open circuit damage may occur to the power switch and so some form of detection
should be present to provide Over-voltage detection/protection.
AL9910/ AL9910A/ AL9910-5
Document number: DS35103 Rev. 8 - 2
11 of 15
www.diodes.com
December 2012
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ALC60481R05 PWR SUP AC-DC 6-48V 1.05A 50.4W
ALV100362R5 POWER SUPPLY AC-DC 36V 2.5A 90W
ALV60361R7 POWER SUPPLY AC-DC 36V 1.7A 61W
ALV80126R5 POWER SUPPLY AC-DC 12V 6.5A 78W
AOZ1083CI IC LED DRVR BUCK CC 1.2A SOT23-6
AOZ1935QI IC LED DRVR WHITE BCKLGT 16QFN
AOZ1977AI IC LED DRVR BCKLGT 16SOIC
AP-104-NT 12V PLUG TRANSFORMER EMPTY CASE
相关代理商/技术参数
AL9910ASP-13 功能描述:LED照明驱动器 300kHz 85 to 277Vac 7.5V Mosfet LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
AL9910EV4 功能描述:AL9910A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:180mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:85 ~ 277 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1
AL9910EV5 功能描述:AL9910A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:240mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:85 ~ 277 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1
AL9910EV6 功能描述:AL9910A 4, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:75mA 输出和类型:4，非隔离 电压 - 输出:- 特性:- 电压 - 输入:90 ~ 132 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1
AL9910EV8 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:Non-Dimmable 120VAC Evaluation Board
AL9910S-13 功能描述:LED照明驱动器 7.5V LED Driver PWM 85 to 265VAC Mosfet RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
AL9910S-13-CUT TAPE 制造商:DIODES 功能描述:AL9910 Series 100 kHz 7.5 V Universal Offline High Voltage LED Driver - SOIC-8
AL9910SP-13 功能描述:LED照明驱动器 300kHz 85 to 277Vac 10V Mosfet LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N